201 lines
7.0 KiB
C
201 lines
7.0 KiB
C
|
/**
|
||
|
|
******************************************************************************
|
||
|
|
* File Name : USART.c
|
||
|
|
* Description : This file provides code for the configuration
|
||
|
|
* of the USART instances.
|
||
|
|
******************************************************************************
|
||
|
|
* This notice applies to any and all portions of this file
|
||
|
|
* that are not between comment pairs USER CODE BEGIN and
|
||
|
|
* USER CODE END. Other portions of this file, whether
|
||
|
|
* inserted by the user or by software development tools
|
||
|
|
* are owned by their respective copyright owners.
|
||
|
|
*
|
||
|
|
* Copyright (c) 2018 STMicroelectronics International N.V.
|
||
|
|
* All rights reserved.
|
||
|
|
*
|
||
|
|
* Redistribution and use in source and binary forms, with or without
|
||
|
|
* modification, are permitted, provided that the following conditions are met:
|
||
|
|
*
|
||
|
|
* 1. Redistribution of source code must retain the above copyright notice,
|
||
|
|
* this list of conditions and the following disclaimer.
|
||
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||
|
|
* this list of conditions and the following disclaimer in the documentation
|
||
|
|
* and/or other materials provided with the distribution.
|
||
|
|
* 3. Neither the name of STMicroelectronics nor the names of other
|
||
|
|
* contributors to this software may be used to endorse or promote products
|
||
|
|
* derived from this software without specific written permission.
|
||
|
|
* 4. This software, including modifications and/or derivative works of this
|
||
|
|
* software, must execute solely and exclusively on microcontroller or
|
||
|
|
* microprocessor devices manufactured by or for STMicroelectronics.
|
||
|
|
* 5. Redistribution and use of this software other than as permitted under
|
||
|
|
* this license is void and will automatically terminate your rights under
|
||
|
|
* this license.
|
||
|
|
*
|
||
|
|
* THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS"
|
||
|
|
* AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT
|
||
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
|
||
|
|
* PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY
|
||
|
|
* RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT
|
||
|
|
* SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
||
|
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
|
||
|
|
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
|
||
|
|
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
|
||
|
|
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
|
||
|
|
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||
|
|
*
|
||
|
|
******************************************************************************
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Includes ------------------------------------------------------------------*/
|
||
|
|
#include "usart.h"
|
||
|
|
|
||
|
|
#include "gpio.h"
|
||
|
|
#include "dma.h"
|
||
|
|
|
||
|
|
/* USER CODE BEGIN 0 */
|
||
|
|
|
||
|
|
/* USER CODE END 0 */
|
||
|
|
|
||
|
|
UART_HandleTypeDef huart4;
|
||
|
|
DMA_HandleTypeDef hdma_uart4_rx;
|
||
|
|
DMA_HandleTypeDef hdma_uart4_tx;
|
||
|
|
|
||
|
|
/* UART4 init function */
|
||
|
|
void MX_UART4_Init(void)
|
||
|
|
{
|
||
|
|
|
||
|
|
huart4.Instance = UART4;
|
||
|
|
huart4.Init.BaudRate = 115200; // Provisionally this can be changed to 921600 for faster transfers, the low power Arduinos will not keep up.
|
||
|
|
huart4.Init.WordLength = UART_WORDLENGTH_8B;
|
||
|
|
huart4.Init.StopBits = UART_STOPBITS_1;
|
||
|
|
huart4.Init.Parity = UART_PARITY_NONE;
|
||
|
|
huart4.Init.Mode = UART_MODE_TX_RX;
|
||
|
|
huart4.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
||
|
|
huart4.Init.OverSampling = UART_OVERSAMPLING_16;
|
||
|
|
if (HAL_UART_Init(&huart4) != HAL_OK)
|
||
|
|
{
|
||
|
|
_Error_Handler(__FILE__, __LINE__);
|
||
|
|
}
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle)
|
||
|
|
{
|
||
|
|
|
||
|
|
GPIO_InitTypeDef GPIO_InitStruct;
|
||
|
|
if(uartHandle->Instance==UART4)
|
||
|
|
{
|
||
|
|
/* USER CODE BEGIN UART4_MspInit 0 */
|
||
|
|
|
||
|
|
/* USER CODE END UART4_MspInit 0 */
|
||
|
|
/* UART4 clock enable */
|
||
|
|
__HAL_RCC_UART4_CLK_ENABLE();
|
||
|
|
|
||
|
|
/**UART4 GPIO Configuration
|
||
|
|
PA0-WKUP ------> UART4_TX
|
||
|
|
PA1 ------> UART4_RX
|
||
|
|
*/
|
||
|
|
GPIO_InitStruct.Pin = GPIO_1_Pin;
|
||
|
|
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||
|
|
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
|
||
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||
|
|
GPIO_InitStruct.Alternate = GPIO_AF8_UART4;
|
||
|
|
HAL_GPIO_Init(GPIO_1_GPIO_Port, &GPIO_InitStruct);
|
||
|
|
|
||
|
|
GPIO_InitStruct.Pin = GPIO_2_Pin;
|
||
|
|
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||
|
|
GPIO_InitStruct.Alternate = GPIO_AF8_UART4;
|
||
|
|
HAL_GPIO_Init(GPIO_2_GPIO_Port, &GPIO_InitStruct);
|
||
|
|
|
||
|
|
/* UART4 DMA Init */
|
||
|
|
/* UART4_RX Init */
|
||
|
|
hdma_uart4_rx.Instance = DMA1_Stream2;
|
||
|
|
hdma_uart4_rx.Init.Channel = DMA_CHANNEL_4;
|
||
|
|
hdma_uart4_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
|
||
|
|
hdma_uart4_rx.Init.PeriphInc = DMA_PINC_DISABLE;
|
||
|
|
hdma_uart4_rx.Init.MemInc = DMA_MINC_ENABLE;
|
||
|
|
hdma_uart4_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
|
||
|
|
hdma_uart4_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
|
||
|
|
hdma_uart4_rx.Init.Mode = DMA_CIRCULAR;
|
||
|
|
hdma_uart4_rx.Init.Priority = DMA_PRIORITY_LOW;
|
||
|
|
hdma_uart4_rx.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
|
||
|
|
if (HAL_DMA_Init(&hdma_uart4_rx) != HAL_OK)
|
||
|
|
{
|
||
|
|
_Error_Handler(__FILE__, __LINE__);
|
||
|
|
}
|
||
|
|
|
||
|
|
__HAL_LINKDMA(uartHandle,hdmarx,hdma_uart4_rx);
|
||
|
|
|
||
|
|
/* UART4_TX Init */
|
||
|
|
hdma_uart4_tx.Instance = DMA1_Stream4;
|
||
|
|
hdma_uart4_tx.Init.Channel = DMA_CHANNEL_4;
|
||
|
|
hdma_uart4_tx.Init.Direction = DMA_MEMORY_TO_PERIPH;
|
||
|
|
hdma_uart4_tx.Init.PeriphInc = DMA_PINC_DISABLE;
|
||
|
|
hdma_uart4_tx.Init.MemInc = DMA_MINC_ENABLE;
|
||
|
|
hdma_uart4_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
|
||
|
|
hdma_uart4_tx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
|
||
|
|
hdma_uart4_tx.Init.Mode = DMA_NORMAL;
|
||
|
|
hdma_uart4_tx.Init.Priority = DMA_PRIORITY_LOW;
|
||
|
|
hdma_uart4_tx.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
|
||
|
|
if (HAL_DMA_Init(&hdma_uart4_tx) != HAL_OK)
|
||
|
|
{
|
||
|
|
_Error_Handler(__FILE__, __LINE__);
|
||
|
|
}
|
||
|
|
|
||
|
|
__HAL_LINKDMA(uartHandle,hdmatx,hdma_uart4_tx);
|
||
|
|
|
||
|
|
/* UART4 interrupt Init */
|
||
|
|
HAL_NVIC_SetPriority(UART4_IRQn, 5, 0);
|
||
|
|
HAL_NVIC_EnableIRQ(UART4_IRQn);
|
||
|
|
/* USER CODE BEGIN UART4_MspInit 1 */
|
||
|
|
|
||
|
|
/* USER CODE END UART4_MspInit 1 */
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void HAL_UART_MspDeInit(UART_HandleTypeDef* uartHandle)
|
||
|
|
{
|
||
|
|
|
||
|
|
if(uartHandle->Instance==UART4)
|
||
|
|
{
|
||
|
|
/* USER CODE BEGIN UART4_MspDeInit 0 */
|
||
|
|
|
||
|
|
/* USER CODE END UART4_MspDeInit 0 */
|
||
|
|
/* Peripheral clock disable */
|
||
|
|
__HAL_RCC_UART4_CLK_DISABLE();
|
||
|
|
|
||
|
|
/**UART4 GPIO Configuration
|
||
|
|
PA0-WKUP ------> UART4_TX
|
||
|
|
PA1 ------> UART4_RX
|
||
|
|
*/
|
||
|
|
HAL_GPIO_DeInit(GPIOA, GPIO_1_Pin|GPIO_2_Pin);
|
||
|
|
|
||
|
|
/* UART4 DMA DeInit */
|
||
|
|
HAL_DMA_DeInit(uartHandle->hdmarx);
|
||
|
|
HAL_DMA_DeInit(uartHandle->hdmatx);
|
||
|
|
|
||
|
|
/* UART4 interrupt Deinit */
|
||
|
|
HAL_NVIC_DisableIRQ(UART4_IRQn);
|
||
|
|
/* USER CODE BEGIN UART4_MspDeInit 1 */
|
||
|
|
|
||
|
|
/* USER CODE END UART4_MspDeInit 1 */
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
/* USER CODE BEGIN 1 */
|
||
|
|
|
||
|
|
/* USER CODE END 1 */
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|